- NEWEST WACOM DRIVER FOR MAC PRO 16 HOW TO
- NEWEST WACOM DRIVER FOR MAC PRO 16 MAC OS X
- NEWEST WACOM DRIVER FOR MAC PRO 16 MAC OS
- NEWEST WACOM DRIVER FOR MAC PRO 16 INSTALL
- NEWEST WACOM DRIVER FOR MAC PRO 16 SERIES
Battery Stats - Can be fixed using ACPIBatteryManager.kext. All RAM is now seen - Follow How to Fix RAM. Graphic Acceleration - *Your Mileage May Very*. Pen Support - works natively without any modification. Multi touch support - thanks to USBInjectAll.kext. ***Not everything has been tested out so there could be more or less working. Hope that Graphic Acceleration is working. Make sure Graphics > Inject Intel is selected. Go to Graphics > ig-platform-id > Enter 0x19270000. Go to Devices > IntelGFX > Enter 0x19268086. Open the ist file in Clover Configure. *Ill also be including my entire clover folder for those who want to take a look* With the kext installed from above and properly editing the values below according to your graphics card you should be good.* *This is how I got mine working which took quite a bit to figure out with incorrect combination kexts and bad values that kept leading to panics or boots that wouldn't finish. Getting Graphic Acceleration to work (For the Iris 550) Install the Wacom Drivers and reboot and you should be good to go.From this point on you don't need the usb installer to get into clover. Copy the efi folder from the installer usb over to the High Sierra Disk.Open Clover Configurator and mount the EFI partition to the bootable usb and the EFI to the Disk with High Sierra installed (which in my case it was empty).
Drivers > USB > 7/8/9 Series USB Support. Drivers > USB > USBInjectAll ***this allows touch support and quick keys, so very important***. Drivers > Misc > Core Graphics Fixup aka WhateverGreen ***This is needed***. Open Multibeast and select and install the following (like I previously stated I'm going in blind so some of these might not be needed). Drag Multibeast and Clover Configurator into a location you will have easy time accessing. If installation is successful the next time you boot into the new Disk you should be presented with the setup walk-through. This time select the new Disk that you just installed High Sierra to and continue on with the installation. When your computer reboots (which will happen several times), spam esc on startup, go back into boot manager, and select the Installation Disk Again. When computer reboots keep installation usb still plugged in and return back to the clover boot menu. Once successfully formatted begin the install for High Sierra. ****Remember the name of your new disk for when booting into it in clover****. If successful, format your external HDD/SSD to GPT and HFS+ (Mac OS Journal). Boot into clover and select the installer USB and pray it works. Select Boot Manager > ~The name of your Installation Media~ Enter the boot manger by spamming esc on startup. Might be able to get away with the mouse as pen is natively supported without modification) Installing Mac OS X: (you will need a mouse and keyboard.
Copy over Clover Configurator, Wacom Driver, and Multibeast onto the USB. Use Unibeast to create the clover boot entry:. Create the usb bootable installer for High Sierra 10.13.6. UEFI OS Fast Boot to Disabled (I did this for safe measure). Enter the Bios Setup Utility and change:. Disable everything applicable unless its already disabled save changes and exit. Get to the secure boot settings by spamming esc during startup and selecting Administer Secure Boot when the bios front page shows up. A Flash Drive at least 8Gb (USB 3.0 makes things a lot faster). I currently have Mac OS X 10.13.6 installed on an external SSD until I can get it working closer to 100% So now that you have my specs, just as a warning your experience can be different from mine depending on you model. Images of pen and touch working and clover are down at the bottom I also am doing this in my spare time so any extra help to making this a more stable and complete system will be greatly appreciated. This is my first hackintosh project that doesn't have a guide to follow so all of this is really new to me and I'm pretty much going into this blind. I have been trying to get some form of a hackintosh for my MobileStudio and I'm finally making progress.
***To any mods, if I have placed this thread in the wrong location I do apologies for doing so*** Building a CustoMac Hackintosh: Buyer's Guide
0 kommentar(er)
